• Anti-carbonation coating.
• Excellent bonding to porous and non-porous surfaces.
• Flexibility allows crack accommodation and concrete expansion.
• Allows thin application by brush, roller or trowel.
• Impermeable to chloride, carbon dioxide and other harmful agents.
• Good frost resistance.
• Breathable film enhances life of the substrate.
• Ideal for portable water tank due to its non-toxic nature.
• Can be applied directly on damp concrete and masonry.
• Best and Economical brush applied solution involving low labour cost.

Surface Preparation
For better adhesion, the substrate must be sound, clean and free from oils, plasters, grease, surface water, paint, corrosion or any surface contaminants. Mechanical abrasion should be carried out with needle gun or grit blasting that helps to roughen the smooth area and to take out dust or loose particles. Surface should be free from any excess water. Any damaged area should be repaired with mortar before application of Seepstop 2PK.

Mixing
Ratio 1 : 3 (Seepstop 2PK Liquid : Seepstop 2PK Powder)* Transfer the Seepstop 2PK liquid part completely in to a clean plastic or steel container and add the Seepstop 2PK powder part to the liquid slowly. Start mixing with a slow speed pneumatic stirrer (300 to 350 rpm) and add powder gradually under stirring. Continue mixing for additional 2 to 3 min to avoid lump formation. Mix smaller quantity so that mixed slurry can be applied within the pot-life period. Keep the slurry under mixing during application. Do not add additional water.

Application
On hot substrates, i.e. over 40°C surface temperature, a primer coat should be applied. Prime only areas that can be coated with Seepstop 2PK before the primer dries. The mix should not be applied at temperature below 10°C.

Seepstop 2PK can be applied by a brush or spray coating by appropriate spray equipment. For better performance, a minimum of 1mm coating thickness is required. This is achieved by two coats. After complete drying, any subsequent coating goes well on this surface.

For areas which experience heavy hydrostatic pressure apply min 2 mm thickness coating with screed above.

1. 4kg (3kg Powder + 1kg liquid)
2. 20kg (15kg Powder + 5kg Liquid) Coverage
3. 6 - 7 Sq.ft/kg/2 coats at 1mm thickness.

All tools and equipment should be washed with fresh water to remove left out slurry completely. Any dried slurry can be removed mechanically. Contact Clov’s Technical support team for more information in the below provided address.

Health and Safety
Contact with the skin and eyes, and dust inhalation should be avoided. Must not be swallowed or inhaled. Wear suitable protective gear, gloves, eye or face protection and dust mask. In case of contact with skin, it should be washed with clean and clear water. In case of eye contact, rinse immediately with water and seek medical advice immediately.

For more details on product safety / application process clarification call our Clov’s Technical Team in below mentioned address.

Fire
SeepStop 2PK is non-inflammable.

Shelf Life
The shelf life of SeepStop 2PK is 12 months provided it is kept unopened in dry condition at temperatures less than 30⁰C.

• Allows escape of Water Vapor.
• Low Labor costs.
• Excellent Crack Accommodation Capacity.
• High Resistance Long-term Weathering.
• Provides excellent barrier to carbon dioxide, chloride and sulphate ions.
• Waterproof - suitable for water retaining structures.
• Requires less Surface preparation.
• Durable in all climate conditions including UV attack.
• Direct Product Application on surface.

The application surface needs to be free of dust, oil, grease, algae, laitance, wax or any foreign matter. The presence of such material will affect the work quality and concrete adhesion on both new and existing surfaces. Remove foreign materials in case of application in deeply damped regions to achieve sound adhesion.

Stir the contents of CloShield WP thoroughly for at least 2 minutes slowly using a drill machine attached with a mixing paddle. Continue stirring during coating and do not re-tamper with water.

The concrete surface has to be even to obtain better results. To obtain the best of waterproofing properties, it is important to understand the rates of application. Apply the material like a paint using a short and stiff brush of 120 – 150 mm width.

If the substrate temperature is below 10ºC, avoid carrying out the application process. Apply CloShield WP in three coats at dry thickness of approximately 1mm. Make sure to apply consecutive coats as soon as the previous coat reaches dry state. In case the previous coat dries out before application of screed, sprinkle coarse sand on the final wet surface to ensure better adhesion.

The equipment and tools should be removed immediately after use. If the material hardens, it has to be removed mechanically.

For more information on our Safety and Application process, contact our Technical Support team on the below mentioned address.

CloShield WP : 4L and 20L

CloShield WP : 0.5L/sq.m/coat (Three Coats)
OverCoating Time : 8 -10 hours at 27°C
CloPrimer : 8-10 sq.m/L (post dilution)

Do not apply coating during rain. Ensure that the surface is in saturated dry state before application. Kindly note that CloShield WP is designed only to foot traffic not vehicular or equipment movement.

Health and Safety
Instruction CloShield WP is non-toxic and is alkaline in nature. Wearing gloves and goggles is prescribed. Splashes to the skin or eyes should be washed off with clean water immediately. In case of prolonged irritation, kindly seek medical advice. Mandatorily, use a dust mask while handling the powder.

Fire
CloShield WP is non-inflammable.

Shelf Life
The shelf life of CloShield WP is 12 months provided that the pack is unopened.